Differences

This shows you the differences between two versions of the page.

--- guides:tracking_guide [2012/12/15 21:14] – jcoxon
+++ guides:tracking_guide [2015/02/05 22:40] (current) – [Internet] updated urls to tracker.habhub.org lz1dev
@@ Line 5: / Line 5: @@
 Another excellent guide can be found at [[http://projecthorus.org/?page_id=336|Project Horus]]
+===== Translations =====
+  * [[guides:tracking_guide:polish|Polski]]
+  * [[guides:tracking_guide:french|Français]]
+  * [[guides:tracking_guide:spanish|Español]]
+  * [[guides:tracking_guide:german|Deutsch]]
+  * [[guides:tracking_guide:latvian|Latvijas]]
+  * [[guides:tracking_guide:slovak|Slovenský]]
+  * [[guides:tracking_guide:russian|русский]]
@@ Line 14: / Line 22: @@
     * Icom IC-7000 - Literally does everything and a little bit more. approx £900
     * AOR AOR8000 - Wideband Receiver (doesn't do Transmitting)
+    * Yupiteru MVT-7100 - Wideband receiver (doesn't do Transmitting)
+    * Kenwood TS-2000 - Similar to the IC-7000 in that it literally does everything but a bit older and cheaper.
+    * Kenwood TH-F7E - Hand Held dual radio with a 2nd wideband multimode receiver. Not as sensitive as other receivers but very portable (and can monitor the local repeater at the same time)
   * [[guides:sdr_tracker|SDR Dongle]] - If you don't fancy investing in an expensive radio receiver, then it is now possible to use a USB DVB-T dongle, based on the Realtek RTL2832U chipset, as an inexpensive tracker. This is a superb way to get involved with HAB'ing and helping out track other people's balloons.
+  * [[http://www.funcubedongle.com/|FUNcube Dongle Pro+]] - An alternative SDR receiver. More sensitive than the cheap SDR dongles but more expensive. Sensitivity is similar to the Radio receivers listed above.
   * Radio Antenna for 70cm - An excellent guide to understanding directional antennas can be found on this [[http://www.youtube.com/watch?v=lslHtCUSfN4&feature=player_embedded|Youtube video]] by Diana Eng of Make Magazine - while its for transmitting its the same concept for receiving!
     * Whip (often included with the receivers) is an omni-directional antenna and is good when the payload is close by but will also pick up other signals and noise.
@@ Line 51: / Line 63: @@
 There is a 30-sec recording of live data [[http://tenbus.co.uk/icaruscapture_30secs.mp3|mp3 version]] and [[http://tenbus.co.uk/icaruscapture_30secs.wav|wav version]]. These files are about 500kB.
+Please practice decoding in OFFLINE mode to eliminate any confusion with old data from this clip keep appearing on the map! You can do this by unchecking "online" on the "DL Client" dropdown. Settings to decode this should be 425Hz shift, 50 Baud, 8 bit ASCII, no parity and 2 stop bits. Decoding the data should look like [[http://i.imgur.com/QZFBp2h.png|this]].
 Unless you are very close, you won't hear anything unless you have line of sight. This means that the balloon usually needs to be above your horizon.
@@ Line 72: / Line 86: @@
 ===== Computer =====
+==== dl-fldigi ====
-==== dl-fldigi ====
 dl-fldigi is an adapted version of the excellent free [[http://www.w1hkj.com/Fldigi.html|FLdigi]] soundcard decoding software. It takes the audio from your radio, decodes the balloon's signal, and then sends the telemetry it's found over the internet to a server running habitat, which plots the payloads position on to the [[http://spacenear.us/tracker/|SpaceNear]] map.
   * First grab the latest version on the projects page: **[[projects:dl-fldigi]]**
-  * Open up dl-fldigi in //hab// mode (now the default mode for OSX). On first running it'll open up a wizard to help setup dl-fldigi for you.
+  * Open up dl-fldigi in //HAB mode// (now the default mode for OSX). On first running it'll open up a wizard to help setup dl-fldigi for you.
 {{guides:wizard1.jpeg?300|}}{{:guides:wizard2.jpg?320|}}{{guides:wizard3.jpeg?300|}}{{guides:wizard4.jpeg?300|}}
@@ Line 99: / Line 111: @@
 [[guides:old_tracking|Tracking with r85 of dl-fldigi]]
+=== RxID or RSID ===
+Not all of the modes are available using the Auto-config facilities, however there is the RxID facility
+where by each transmission is preceded by a short burst of data that identifies the mode that will follow.
+It also has the feature of being tracked by the AFC so it will also allow the receiver to be adjusted to
+the correct centre frequency.  To select this feature, turn on RxID as below:
+{{:guides:dl-fldigi-rxid.jpg}}
+To setup the configuration for RxID, select the Configure | IDs option:
+{{:guides:dl_fldigi-ids.jpg}}
+Turn on all the modes and select the options required, the "Search all Passband" and "Marker" are good defaults to choose:
+{{:guides:dl-fldigi-rsid.jpg}}
+Finally Save the configuration and close the window, these should then remain as your default settings.
 ===== Internet =====
   * dl-fldigi forwards the strings to the central server.
   * Statistics and data can be found here [[http://habitat.habhub.org/]]
-  * The server does further checks and then will post the points to the [[http://spacenear.us/tracker/|spacenear.us tracker]]
+  * The server does further checks and then will post the points to the [[http://tracker.habhub.org/|habhub tracker]]
+  * You can also track using Google Earth by using the following link http://tracker.habhub.org/track.kml, for more details on how to get the best out of Google Earth see [[:using_google_earth|]]
   * If you wish to try out receiving and decoding data without posting to the central server, then please refer to version specific instructions on the [[projects:dl-fldigi|dl-fldigi project page]].