Differences

This shows you the differences between two versions of the page.

--- projects:jimbob:habtrk [2013/07/30 21:32] – kevwal
+++ projects:jimbob:habtrk [2013/08/08 16:58] (current) – kevwal
@@ Line 1: / Line 1: @@
-==== Dev board 1 ====
+==== PCB Version 006 Board 1 ====
 NCP1400 Voltage Reg at 1.8v
@@ Line 9: / Line 9: @@
 RFM22B Radio
+{{http://i.imgur.com/AT0nboq.jpg?nolink&200|}}
+{{http://i.imgur.com/0rDx5Ef.jpg?nolink&200|}}
@@ Line 55: / Line 60: @@
 ==== Arduino ====
-Arduinio Software Serial library doesn't support 4mhz clocks - so I created a SoftwareSerial4Mhz with just a 9600 baud line - not yet tested
+Arduinio Software Serial library doesn't support 4mhz clocks - so I created a SoftwareSerial4Mhz with just a 9600 baud line - works fine, verified timing with scope to the best of my ability.
-Arduinio wiring.c does not support 4Mhz clocks, so delays in the code will be wrong - either edit your delays (/2) or edit wiring.c
+<code>
+#elif F_CPU == 4000000
+static const DELAY_TABLE table[] PROGMEM =
+{
+  //  baud    rxcenter    rxintra    rxstop  tx
+  { 9600,     19,         54,        54,     51,    },
+};
+const int XMIT_START_ADJUSTMENT = 3;
+</code>
+Arduinio wiring.c does not support 4Mhz clocks, so delays in the code will be wrong I think - either edit your delays (/2) or edit wiring.c
 Added a section to boards.txt to tell the Arduinio IDE about the board:
@@ Line 78: / Line 95: @@
 avrispmkiis.protocol=stk500v2
 </code>
 ==== Checking ====
@@ Line 85: / Line 101: @@
+===== Habhub Payload Config =====
+Using the form [[http://habitat.habhub.org/genpayload/|here]] I generated a payload config:
+Payload Name: G7PMO $$HABTRK
+Primary, 434.150, USB, RTTY, 470, ASCII-7, 50 Baud, Parity none, 1 Stop bits.
+{"type":"payload_configuration","name":"G7PMO $$HABTRK","time_created":"2013-08-03T12:21:33+01:00","metadata":{"description":"G7PMO's HABTRK Tracker"},"transmissions":[{"frequency":434150000,"modulation":"RTTY","mode":"USB","encoding":"ASCII-7","parity":"none","stop":1,"shift":470,"baud":50,"description":"Primary"}],"sentences":[{"protocol":"UKHAS","callsign":"HABTRK","checksum":"crc16-ccitt","fields":[{"name":"sentence_id","sensor":"base.ascii_int"},{"name":"time","sensor":"stdtelem.time"},{"name":"latitude","sensor":"stdtelem.coordinate","format":"dd.dddd"},{"name":"longitude","sensor":"stdtelem.coordinate","format":"dd.dddd"},{"name":"altitude","sensor":"base.ascii_int"},{"name":"satellites","sensor":"base.ascii_int"},{"name":"battery","sensor":"base.ascii_int"},{"name":"temperature_rfm22b","sensor":"base.ascii_int"}],"filters":{"post":[{"filter":"common.numeric_scale","factor":0.001,"round":3,"source":"battery","type":"normal"},{"filter":"common.invalid_gps_lock","ok":[4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20],"source":"satellites","type":"normal"}]},"description":"$$HABTRK Std format"}]}
+Doc ID: e55cc3ffb42062c70087dae3d9520903
+Note the filter I use to identify if I have a satellite fix "{"filter":"common.invalid_gps_lock","type":"normal","ok":[4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20],"source":"satellites"}"
+I should really implement another variable in the sentence to define lock directly for the PUBX code, but I am told the above should do what I want it to do.