UKHAS Wiki

UK High Altitude Society

User Tools

Site Tools


projects:ava

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
projects:ava [2011/06/17 14:36] upuprojects:ava [2016/09/08 14:48] (current) – Removed link to HAB Supplies. upu
Line 2: Line 2:
  
 High Altitude Balloon Project High Altitude Balloon Project
-Based in West Yorkshire run by Anthony Stirk. +Based in West Yorkshire run by Anthony Stirk M0UPU
-This is project is just waiting on a NOTAM for launch permission at the [[http://www.deershedfestival.com|Deer Shed Festival]], North Yorkshire on the 24th of July 2011 + 
 +==== Overview ==== 
 + 
 +Project AVA covers variety of boards and launches I've done.  
 + 
 +^ Date     ^ Mission ^ Balloon^ Payload^ Altitude^ PCB ^  
 +| 01/10/11 | Ava| Hwoyee 1600 |1600g| UnKnown > 34km | Ava  | 
 +| 31/03/12 | Ava2| Hwoyee 1600 |1500g| 38257 | Ava2 | 
 +| 14/03/12 | pAva| Hwoyee 1600 |65g| 43337 | picoAva | 
 +| 14/03/12 | uAva| Hwoyee 1200 |1000g| 39997 | µAvaNut | 
 + 
 +==== Ava ==== 
 + 
 +My first launch was on a very sunny day in October. Due to relative inexperience we didn't put enough gas in the balloon and it ended up floating out to sea. Additionally the GPS failed due to interference from the small video camera. Recovery was initiated by boat and despite the failure of all the electronics due to salt water the pictures were spectacular.  
 + 
 +Full write up here : [[http://ava.upuaut.net/?p=155]] , here [[http://ava.upuaut.net/?p=185]] and here [[http://ava.upuaut.net/?p=212]] 
 + 
 +==== Ava2 ==== 
 + 
 +Ava2 was a total resign of the PCB and was launched along with Dave Akermans Cloud payload. The mission was to test the new design of PCB and to fly a heated U/V filtered cameraThe camera was a total failure with bad steaming up however the new PCB performed perfectly and was tracked from launch to landing. Recovery from a tree was interesting. Full write up here : [[http://ava.upuaut.net/?p=286]] 
 + 
 +==== pAva ==== 
 + 
 +[[http://ava.upuaut.net/?p=295|pAva]] was another prototype board this time using the RFM22B and the chip antenna to create an ultra light (5g) PCB tracker. As there was a possibility of float we fit 2 AA batteries which would have powered it for 36 hours+. However pAVA climbed to over 43km before the balloon failed. The decent took a few hours as the balloon split and acted like a huge parachute. In the end pAVA took the 4th highest altitude in the world for an amateur balloon. pAVA was kindly recovered by Dave Akerman from a field full of wet triffids. See [[http://ava.upuaut.net/?p=315]]. 
 + 
 +==== uAva ==== 
 + 
 +Testing the µAvaNut PCB and flying a GoPro camera this was another sucessful flight. Unfortunately the Gopro footage wasn't perfect as the lense again steamed up. Won't be flying the case next time. Write up in the same article as listed above. 
 + 
 +AVA is always very pink. 
 + 
 +==== About me ==== 
 + 
 +When I'm not launching pink boxes I am the technical director of an IT Consultancy in West Yorkshire.  
 + 
 + 
 + 
  
 Full blog here : Full blog here :
projects/ava.1308321393.txt.gz · Last modified: 2011/06/17 14:36 by upu

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki