Differences

This shows you the differences between two versions of the page.

--- guides:ublox6 [2012/09/05 08:18] – costyn
+++ guides:ublox6 [2016/09/08 14:52] (current) – Up upu
@@ Line 7: / Line 7: @@
 **WARNING : uBLOX 6 Chips are rated at 3.3v so you can't just plug this into an 5V Arduino board or a PC serial connection as these run at 5V.**
-You can purchase a seperate level convertor from [[http://www.sparkfun.com/products/8745|Sparkfun]] or use a breakout with the integral level convertor available from [[http://ava.upuaut.net/store|HAB Supplies]].
+You can purchase a seperate level converter from [[http://www.sparkfun.com/products/8745|Sparkfun]] or use a breakout with the integral level converter available from [[https://store.uputronics.com|Uputronics]].
-The MAX-6 Chip, Sarantel antenna and populated breakout boards can be purchased from [[http://ava.upuaut.net/store|HAB Supplies]].
+The MAX-6 Chip, Sarantel antenna and populated breakout boards can be purchased from [[https://store.uputronics.com|Uputronics]].
 ===== Hardware =====
@@ Line 15: / Line 15: @@
 Unlike the Falcom FSA03 these units are just supplied as a standalone surface mount chip without an antenna. To use it you will need to use a breakout board/design your own board.
-There are Eagle breakout boards designed by Upu with assistance from Darkside available on Github :
-NEO-6 :\\
+If you want to integrate the units into your own design both modules and antennas are in [[https://www.dropbox.com/s/qytveix714ocw11/Ava.lbr|Ava.lbr]].
-[[https://github.com/Upuaut/Eagle-Libraries/tree/master/uBLOX%20NEO-6Q%20Breakout|https://github.com/Upuaut/Eagle-Libraries/tree/master/uBLOX%20NEO-6Q%20Breakout]] files :\\
-uBlox_NEO-6Q_Breakout.brd - Board with Sarantel Antenna\\
-uBlox_NEO-6Q_Breakout.sch \\
-The board is designed to be use with the passive Sarantel quadrifilar helix antenna ([[http://www.spkecl.com/style/frame/templates8/product_detail.asp?lang=2&customer_id=617&name_id=18379&content_set=color_5&rid=19996&id=82626|Sarantel SR-1202]]). The chip does support active antennas but does not supply power to them.
-MAX-6 :\\
-[[https://github.com/Upuaut/Eagle-Libraries/tree/master/MAX6%20Breakout|https://github.com/Upuaut/Eagle-Libraries/tree/master/MAX6%20Breakout]] files :\\
-max6_breakout.brd - Board with Sarantel Antenna\\
-max6_breakout.sch\\
-max6_breakout_1575AT43A40.brd - Board with Ceramic Chip Antenna\\
-max6_breakout_1575AT43A40.sch\\
-max6_breakout_lc.brd - As above but with 5v t0 3.3v Level Convertor on board.\\
-max6_breakout_lc.sch\\
-NOTE : These libaries are in Eagle 6.1 Format so won't work with Eagle 5.X. \\
-If you want to integrate the units into your own design both modules and antennas are in [[https://github.com/Upuaut/Eagle-Libraries/blob/master/ava.lbr|Ava.lbr]].
@@ Line 76: / Line 57: @@
   Serial.println("Setting uBlox nav mode: ");
   uint8_t setNav[] = {
-xB5, 0x62, 0x06, 0x24, 0x24, 0x00, 0xFF, 0xFF, 0x06, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10, 0x27, 0x00, 0x00, 0x05, 0x00, 0xFA, 0x00, 0xFA, 0x00, 0x64, 0x00, 0x2C, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16, 0xDC                        };
+xB5, 0x62, 0x06, 0x24, 0x24, 0x00, 0xFF, 0xFF, 0x06, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10, 0x27, 0x00, 0x00,
+x05, 0x00, 0xFA, 0x00, 0xFA, 0x00, 0x64, 0x00, 0x2C, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16, 0xDC };
   while(!gps_set_sucess)
   {
@@ Line 208: / Line 191: @@
 }
 </code>
 ===== Hardware Serial Configuration Example =====
@@ Line 219: / Line 201: @@
 Connect UB6 5V on the board to 5V on the Arduino\\
 Connect UB6 GND on the board to GND on the Arduino\\
-Connect UB6 TX on the board to pin 1 TX\\
+Connect UB6 RX on the board to pin 1 TX\\
-Connect UB6 RX on the board to pin 0 RX\\
+Connect UB6 TX on the board to pin 0 RX\\
 Connect UM232R pin DB0 to pin 4 on the Arduino\\
 Connect UM232R pin DB1 to pin 5 on the Arduino\\
@@ Line 230: / Line 212: @@
 /05/2012 2E0UPU
-  Initialise the GPS Module in Flight Mode and then echo's out the NMEA Data to the Software Serial.
+  Initialise the GPS Module in Flight Mode and then echoes out the NMEA Data to the Software Serial.
   This example code is in the public domain.
@@ Line 253: / Line 235: @@
   mySerial.println("Setting uBlox nav mode: ");
   uint8_t setNav[] = {
-xB5, 0x62, 0x06, 0x24, 0x24, 0x00, 0xFF, 0xFF, 0x06, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10, 0x27, 0x00, 0x00, 0x05, 0x00, 0xFA, 0x00, 0xFA, 0x00, 0x64, 0x00, 0x2C, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16, 0xDC                      };
+xB5, 0x62, 0x06, 0x24, 0x24, 0x00, 0xFF, 0xFF, 0x06, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10, 0x27, 0x00, 0x00,
+x05, 0x00, 0xFA, 0x00, 0xFA, 0x00, 0x64, 0x00, 0x2C, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16, 0xDC };
   while(!gps_set_sucess)
   {
@@ Line 465: / Line 449: @@
 For details see page 52 of the UBX protocol specification "Proprietary Messages, UBX00".
+You can use a modified version of the [[http://arduiniana.org/libraries/tinygps/|TinyGPS]] library to parse PUBX sentences – [[https://github.com/x-f/TinyGPS_UBX|TinyGPS_UBX]].
 ===== Images ======